h3c 终结者配置
h3c 终结者配置
来自专栏网路工程师
华三终结者配置
5.1 直通模式集中转发关键配置
#
[AC] interface vlan-interface 100
[AC-Vlan-interface100] ip address 10.1.9.58 16
# 创建AP模板，选择AP型号并配置序列号。
[AC] wlan ap 1020 model wt1020
[AC-wlan-ap-1020] serial-id DPPMWWB123456
[AC-wlan-ap-1020] wt version 1 //默认超瘦模式切换直通时需要重启本体
[AC] wlan ap ap1 model wtu430
[AC-wlan-ap-ap1] serial-id 219801A0CNC138011454
创建无线服务模板，并将无线服务模板绑定到AP的Radio介面。
# 配置无线无线服务模板service1，配置SSID为h3c-edu，并使能服务模版。
<AC> system-view
[AC] wlan service-template service1
[AC-wlan-st-service1] ssid h3c-edu
[AC-wlan-st-service1] service-template enable
[AC-wlan-st-service1] quit
# 配置射频，指定工作信道为157。
[AC] wlan ap ap1
[AC-wlan-ap-ap1] radio 1
[AC-wlan-ap-ap1-radio-1] channel 157
# 将无线服务模板service1绑定到Radio 1介面。
[AC-wlan-ap-ap1-radio-1] service-template service1 vlan 3
[AC-wlan-ap-ap1-radio-1] radio enable
5.2 直通模式本地转发关键配置
#
[AC] interface vlan-interface 100
[AC-Vlan-interface100] ip address 10.1.9.58 16
# 创建AP模板，选择AP型号并配置序列号。
[AC] wlan ap 1020 model wt1020
[AC-wlan-ap-1020] serial-id DPPMWWB123456
[AC-wlan-ap-1020] wt version 1 //默认超瘦模式切换直通时需要重启本体
[AC-wlan-ap-1020] map-configuration cfa0:/1020.txt
[AC] wlan ap ap1 model wtu430
[AC-wlan-ap-ap1] serial-id 219801A0CNC138011454
[AC-wlan-ap-ap1] map-configuration cfa0:/430.txt
创建无线服务模板，并将无线服务模板绑定到AP的Radio介面。
# 配置无线无线服务模板service1，配置SSID为h3c-edu，并使能服务模版。
<AC> system-view
[AC] wlan service-template service1
[AC-wlan-st-service1] ssid h3c-edu
[AC-wlan-st-service1] client forwarding-location ap
[AC-wlan-st-service1] service-template enable
[AC-wlan-st-service1] quit
# 配置射频，指定工作信道为157。
[AC] wlan ap ap1
[AC-wlan-ap-ap1] radio 1
[AC-wlan-ap-ap1-radio-1] channel 157
# 将无线服务模板service1绑定到Radio 1介面。
[AC-wlan-ap-ap1-radio-1] service-template service1 vlan 3
[AC-wlan-ap-ap1-radio-1] radio enable
#本体map文件
system-view
Vlan 3
interface GigabitEthernet1/0/1 //上联交换机
port link-type trunk
port trunk permit vlan 3
#分体map文件
system-view
vlan 3
interface GigabitEthernet1/0/1
port link-type trunk
port trunk permit vlan 3
#上联交换机配置
interface GigabitEthernet1/0/18
port link-type trunk
port trunk permit vlan 3 100
port trunk pvid vlan 100
5.3 超瘦模式集中转发关键配置
#
[AC] interface vlan-interface 100
[AC-Vlan-interface100] ip address 10.1.9.58 16
# 创建AP模板，选择AP型号并配置序列号。
[AC] wlan ap ap1 model WTU420H
[AC-wlan-ap-ap1] serial-id 219801A0CNC138011454
[AC] wlan ap 1020 model wt1020
[AC-wlan-ap-1020] serial-id DPPMWWB123456
[AC-wlan-ap-1020] wt version 2 //如果是WT1024-X则配置成wt version 3
[AC-wlan-ap-1020] map-configuration cfa0:/1020.txt
创建无线服务模板，并将无线服务模板绑定到AP的Radio介面。
# 配置无线无线服务模板service1，配置SSID为h3c-edu，并使能服务模版。
<AC> system-view
[AC] wlan service-template service1
[AC-wlan-st-service1] ssid h3c-edu
[AC-wlan-st-service1] service-template enable
[AC-wlan-st-service1] quit
# 配置射频，指定工作信道为157。
[AC] wlan ap ap1
[AC-wlan-ap-ap1] radio 1
[AC-wlan-ap-ap1-radio-1] channel 157
# 将无线服务模板service1绑定到Radio 1介面。
[AC-wlan-ap-ap1-radio-1] service-template service1 vlan 3
[AC-wlan-ap-ap1-radio-1] radio enable
#本体map文件
此处以分体在本体7号口安装为例
system-view
port-isolate group 1 //配置分体有线口埠隔离，防止广播风暴
Vlan 4
interface GigabitEthernet1/0/1
port link-type trunk
port trunk permit vlan 4
slot 7
provision model WTU420H //由于分体必须关联本体才能生成下行介面很多情况下并不能满足，这里使用预配置解决
interface Ethernet1/7/1
port access vlan 4
port-isolate enable group 1
interface Ethernet1/7/2
port access vlan 4
port-isolate enable group 1
interface Ethernet1/7/3
port access vlan 4
port-isolate enable group 1
interface Ethernet1/7/4
port access vlan 4
port-isolate enable group 1
#上联交换机配置
interface GigabitEthernet1/0/18
port link-type trunk
port trunk permit vlan 4 100
port trunk pvid vlan 100
5.4 超瘦模式本地转发关键配置
#
[AC] interface vlan-interface 100
[AC-Vlan-interface100] ip address 10.1.9.58 16
# 创建AP模板，选择AP型号并配置序列号。
[AC] wlan ap ap1 model WTU420H
[AC-wlan-ap-ap1] serial-id 219801A0CNC138011454
[AC] wlan ap 1020 model wt1020
[AC-wlan-ap-1020] serial-id DPPMWWB123456
[AC-wlan-ap-1020] wt version 2 //如果是WT1024-X则配置成wt version 3
[AC-wlan-ap-1020] map-configuration cfa0:/1020.txt
创建无线服务模板，并将无线服务模板绑定到AP的Radio介面。
# 配置无线无线服务模板service1，配置SSID为h3c-edu，并使能服务模版。
<AC> system-view
[AC] wlan service-template service1
[AC-wlan-st-service1] ssid h3c-edu
[AC-wlan-st-service1] client forwarding-location ap
[AC-wlan-st-service1] service-template enable
[AC-wlan-st-service1] quit
# 配置射频，指定工作信道为157。
[AC] wlan ap ap1
[AC-wlan-ap-ap1] radio 1
[AC-wlan-ap-ap1-radio-1] channel 157
# 将无线服务模板service1绑定到Radio 1介面。
[AC-wlan-ap-ap1-radio-1] service-template service1 vlan 3
[AC-wlan-ap-ap1-radio-1] radio enable
#本体map文件
此处以分体在本体5号口安装为例
system-view
port-isolate group 1
Vlan 3 to 4
interface GigabitEthernet1/0/1
port link-type trunk
port trunk permit vlan 3 4
slot 5
provision model WTU420H
interface Ethernet1/5/1
port access vlan 4
port-isolate enable group 1
interface Ethernet1/5/2
port access vlan 4
port-isolate enable group 1
interface Ethernet1/5/3
port access vlan 4
port-isolate enable group 1
interface Ethernet1/5/4
port access vlan 4
port-isolate enable group 1
#上联交换机配置
interface GigabitEthernet1/0/18
port link-type trunk
port trunk permit vlan 3 4 100
port trunk pvid vlan 100
推荐阅读：
